Which Is The Best Photoresist Fim 3M

Product Description

Hand-Masker advanced masking film in paint bond technology. This is the most flake resistant film for multi-coat paint applications. Use for paint masking and overspray protection. It use to protect surfaces and contain dust. Strong and flexible, easily unfolds to cover small or large areas. Measures 90-feet length by 99-Inch width by 4-mil thickness.

From the Manufacturer

Hand-Masker advanced masking film in paint bond technology. This is the most flake resistant film for multi-coat paint applications. Use for paint masking and overspray protection. It use to protect surfaces and contain dust. Strong and flexible, easily unfolds to cover small or large areas. Measures 90-feet length by 99-Inch width by 4-mil thickness.

Feature:
1.5 mil thickness of dry film can be completely cover a hole of 0.25 inches
The dry film can be used in the most ordinary plating solution, no wrinkle, no discoloration

Operating steps:
1, grinding CCL, this simple, using the finest polished clean water frosted paper on the line
2, removing film, photographic film is sandwiched between two layers of film, the first side can make use of transparent tape tear torn, try a few on the line
3, and then foil, copper clad laminates can look a little cleaner, pasted, try not to have bubbles.
4, good paste membrane used presses, not too hot, about 100 degrees from the fixing.
5, the printed circuit board film, suggestion is to use film, the fine could reach the highest degree of accuracy if you did not ask for the paper to print it with sulfuric acid trip.
6, the printed circuit on the photographic plate (Note: Dry film is negative, so to highlight the print, which we usually use photographic plate opposite) with ordinary energy-saving lamps 10 or so, if there is exposure Machine 1 minutes on the line, the sun not tried, it should be 30 seconds -60 seconds, the exposure process Obviously, since the photosensitive film will change color when exposed to light, the light becomes dark blue. You will easily see your circuit diagram appeared on the board.
7, developing and tear the protective film on the front panel, into the developer (developer according 1:100,10 gram Total 1L of water) to be used when developing a little harder stick cotton wipe board.
8, etching, this goes without saying (ferric chloride etchant environmental For protection, hydrochloric acid + hydrogen peroxide, etc.) is recommended environmental etching shop, fast, clean, no odor.
9, after a good CCL etching, stripping, from film watered by 1:60 or 70, the board bubble like a few minutes
10, after the completion of the board, very pretty good, most dense line spa

Description:
Photographic film, also known as dry film, is used to make PCB board, stick it on top of the PCB, it will become a sensitive circuit board. This dry film has excellent ability to cover holes, excellent adhesion to almost all surfaces. Suitable for plating, hole covering, and the etching process. High resolution, image clarity after exposure.

Steps of use:
1. Film uncovering, the photographic film is sandwiched between two layers of films.
2. Film pasting, clean and paste flat.
3. Heat slightly to fix with electric iron.
4. Print circuit board film.
5. Exposure
6. Develop
7. Etch
8. Demould

Specification:
Color: black
Material: Plastic
Dimension: 30cm×500cm / 11.8×197in
Weight: approx. 150g

Package List:
1 × Photosensitive film

Specification:
Condition: 100% Brand New
Weight: Approx. 55g / 1.9oz
Size: Approx. 1 * 0.3m / 3.3 * 1.0ft

Package List:
1 * Photosensitive Dry Film

Operating Steps:
1. Uncover the film, the photosensitive film is sandwiched between the two layers of film, first tear off one side, a little difficult to tear, try a few more
2. Then film, the copper plate can be slightly cleaned, flattened, try not to have bubbles
3. After the paste, the iron is slightly heated, not too hot, to fix
4. Print circuit board film, it is recommended to use film, you can achieve the highest fineness, if you do not require precision with sulfuric acid paper to print.
5. Exposure, put the printed pattern on the photosensitive plate, use ordinary energy-saving lamps for about 30 minutes, if there is an exposure machine for 1 minute, the sun has not been tried, it should be about 15 minutes, the exposure process is obvious, because the photosensitive The film changes color when exposed, and changes from light to dark blue. You will easily see your circuit diagram appear on the board.

Description:
This photosensitive dry film has great adaptive capacity to different material. It is used to make PCB board, stick it on top of the PCB, it will become a sensitive circuit board. Suitable for usual plating bath, no wrinkle or color error. Excellent ability to cover holes, and excellent adhesion to almost all surfaces.

Specification:
Condition: 100% Brand New
Weight: Approx. 55g / 1.9oz
Size: Approx. 1 × 0.3m / 3.3 × 1.0ft

Package List:
1 × Photosensitive Dry Film

Steps of use:
1. Film uncovering, the photographic film is sandwiched between two layers of films.
2. Film pasting, clean and paste flat.
3. Heat slightly to fix with electric iron.
4. Print circuit board film.
5. Exposure
6. Develop
7. Etch
8. Demould

Established in 2011, ELEGOO is a thriving technology company dedicated to open-source hardware research & development, production and marketing. Our own Quality Management Team will secure the premium quality of our products and we would like to receive your valuable suggestions for our products and make your idea come true listing: 1pcs Power Supply Module WARNING: Pls. do not use the voltage higher than 9V 1pcs 400 tie-points Breadboard 1pcs 65 Jumper Wire 20pcs Female-to-male DuPont Wire 1pcs Active Buzzer 1pcs Passive Buzzer 1pcs Precision Potentiometer 1pcs IC 4N35 1pcs IC 74HC595 5pcs Diode Rectifier (1N4007) 5pcs NPN Transistor (PN2222) 2pcs Photoresist or 1pcs Thermistor 10pcs Button (small) 10pcs White LED 10pcs Yellow LED 10pcs Blue LED 10pcs Green LED 10pcs Red LED 1pcs RGB LED 2pcs Pin header (40pin) 10pcs 22pf Ceramic Capacitor 10pcs 104 Ceramic Capacitor 5pcs Electrolytic Capacitor (10UF 50V) 5pcs Electrolytic Capacitor (100UF 50V) 10pcs Resistor (10R) 10pcs Resistor (100R) 30pcs Resistor (220R) 10pcs Resistor (330R) 10pcs Resistor (1K) 10pcs Resistor (2K) 10pcs Resistor (5K1) 10pcs Resistor (10K) 10pcs Resistor (100K) 10pcs Resistor (1M).

Features:
Photographic film, also known as dry film, is used to make PCB board.
Stick it on top of the PCB, it will become a sensitive circuit board.
Suitable for plating, hole covering, and the etching process.
Excellent ability to cover holes.
High Resolution.
Excellent adhesion to almost all surfaces.
Image clarity after exposure.
Front-panel is very clean after developed.

Etching:
The dry film is resistant to most of the acid etching solution,
the PH value can be resistant to most alkaline etching solution between PH8.0 ~8.5.

Cover hole:
1.5 mil dry film can fully cover a 0.25 inches thickness hole.

Plating:
The dry film is available in most common use of the plating bath, no wrinkles, no color.

Specification:
Dry Film Photoresist Size: approx. 30cm*500cm/0.98*16.4ft

Note:
Please allow 1-3mm differs due to manual measurement.
Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding.

Package content:
1 x Dry Film Photoresist

Our Promise to Readers

We keep receiving tons of questions of readers who are going to buy photoresist fim 3m, eg:

• What are Top 10 photoresist fim 3m for 2020, for 2019, for 2018 or even 2017 (old models)?
• What is Top 10 photoresist fim 3m to buy?
• What are Top Rated photoresist fim 3m to buy on the market?
• or even What is Top 10 affordable (best budget, best cheap or even best expensive!!!) photoresist fim 3m?…
• All of these above questions make you crazy whenever coming up with them. We know your feelings because we used to be in this weird situation when searching for photoresist fim 3m.
• Before deciding to buy any photoresist fim 3m, make sure you research and read carefully the buying guide somewhere else from trusted sources. We will not repeat it here to save your time.
• You will know how you should choose photoresist fim 3m and What you should consider when buying the photoresist fim 3m and Where to Buy or Purchase the photoresist fim 3m. Just consider our rankings above as a suggestion. The final choice is yours.
• That’s why we use Big Data and AI to solve the issue. We use our own invented, special algorithms to generate lists of Top 10 brands and give them our own Scores to rank them from 1st to 10th.
• You could see the top 10 photoresist fim 3m of 2020 above. The lists of best products are updated regularly, so you can be sure that the information provided is up-to-date.
• You may read more about us to know what we have achieved so far. Don’t hesitate to contact us if something’s wrong or mislead information about photoresist fim 3m.

Conclusion

By our suggestions above, we hope that you can found photoresist fim 3m for you.Please don’t forget to share your experience by comment in this post. Thank you!