hometechfocus 
Nowadays, there are so many products of 3d printer thermistor and heating element in the market and you are wondering to choose a best one. You have searched for 3d printer thermistor and heating element in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings 3d printer thermistor and heating element which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
Ewigkeit 12V 40W Ceramic Cartridge Heater and 3950 100K NTC Thermistor with Female Pin Head for RepRap 3D Printer Heatbed or Hot End
- Thermistor Color : white,Cartridge Heater Material: 304 Stainless Steel
- Voltage: 12v, Power: 40w,Diameter: 6mm
- Length: 20mm
- Temperature sensor 100KΩ accuracy of ± 1%
- Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring
- Support for NTC 3950 is included in Marlin firmware, use TEMP_SENSOR 11 in firmware configuration
BCZAMD 24V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 24V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 24V 50W Ceramic Cartridge Heater
BCZAMD 12V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 12V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 12V 50W Ceramic Cartridge Heater
Conclusion
By our suggestions above, we hope that you can found 3d printer thermistor and heating element for you.Please don’t forget to share your experience by comment in this post. Thank you!
